The school bus endorsement has its own set of rules on top of the passenger endorsement. Mirrors, loading and unloading kids, railroad crossings, and emergency evacuations are all big parts of it.

These 15 questions cover all of that. Loading and unloading is where the most serious mistakes happen, so it gets a lot of attention on the test.

  1. Question 1 of 15

    The crossing gate fails to extend during the pre-trip inspection. What should the driver do?

    Show answerHide answer

    Answer: C. Do not use the bus for student transport until the crossing gate is repaired, if the bus is equipped with one

    If a school bus is equipped with a crossing gate, the driver should verify it extends and retracts properly. If it fails to extend, students may pass too close to the front of the bus. The driver should report the defect and not use the bus for student transport until the crossing gate is repaired or the proper substitute bus/procedure is used.

  2. Question 2 of 15

    How should a school bus driver account for students after an evacuation?

    Show answerHide answer

    Answer: A. Use a passenger list if available, perform a visual head count, and check the bus only if it is safe to do so

    After evacuation, the driver should account for students using a passenger list if available and a visual head count at the safe gathering location. If it is safe to do so, the bus may be checked for anyone left behind. If a student is missing, the driver should report it to first responders immediately.

  3. Question 3 of 15

    Why must the service door be checked during a school bus inspection?

    Show answerHide answer

    Answer: B. Students use it 50-100+ times per route; defective doors can catch clothing/backpacks (drag risk), trap fingers, or fail to seal (cold air, emissions)

    The service door is used repeatedly during a route as students board and exit. Door defects can catch backpack straps or clothing, pinch fingers, or fail to close fully. The driver should verify the service door opens, closes, seals, and operates safely before students board.

  4. Question 4 of 15

    At a student stop with red lights flashing and stop arm extended, a car illegally passes the bus while students are waiting to cross. What should the driver do?

    Show answerHide answer

    Answer: A. HOLD students back , do NOT signal them to cross until traffic in ALL lanes has fully stopped; report illegal passing to dispatch with vehicle description if possible

    If a vehicle illegally passes while students are waiting to cross, the driver should hold students back and not signal them to cross until all lanes are stopped and it is safe. The driver should report the passing vehicle to dispatch or the proper authority with a description or plate number if safely available. Student safety comes before identifying the violator.

  5. Question 5 of 15

    What should a school bus driver check about emergency exits?

    Show answerHide answer

    Answer: C. All required emergency exits, such as doors, push-out windows, and roof hatches, are clearly marked, accessible, and working properly

    School buses have multiple emergency exits, which may include a rear emergency door, side emergency door, push-out windows, and roof hatches depending on the bus. The driver should verify that all required exits are clearly marked, open properly, are not blocked, and have working alarms or warning devices if equipped.

  6. Question 6 of 15

    Which railroad crossing action is unsafe and prohibited for a school bus driver?

    Show answerHide answer

    Answer: C. Shifting gears while crossing the tracks , a missed shift could leave the bus stalled on the rails

    Do not shift gears while crossing railroad tracks. A missed shift could leave the bus stalled on the rails. The driver should select the proper gear before entering the crossing, maintain that gear across the tracks, and shift only after the bus is fully clear.

  7. Question 7 of 15

    What is the proper general sequence for activating school bus warning lights at a student stop?

    Show answerHide answer

    Answer: D. Activate amber warning lights before the stop, come to a complete stop, then open the service door so red lights and stop arm activate if equipped

    A common school bus stopping sequence is to activate amber warning lights before the stop according to state law or local procedure, come to a complete stop, set the brake as required, and open the service door so the red flashing lights and stop arm activate if equipped. After students are safely loaded, unloaded, and clear, the driver closes the door, checks traffic and mirrors, and proceeds when safe.

  8. Question 8 of 15

    A student must cross the road after unloading. What should the driver do before signaling the student to cross?

    Show answerHide answer

    Answer: D. Check all traffic lanes, confirm traffic has stopped, watch for illegal passing, then signal the student only when it is safe

    Before signaling a student to cross, the driver should check traffic in all directions and all lanes, confirm vehicles have stopped, and watch for drivers who may pass illegally. The student should not be signaled to cross until the driver is sure it is safe.

  9. Question 9 of 15

    Which defect most directly affects student loading safety?

    Show answerHide answer

    Answer: B. Stop arm does not extend

    Stop arm failure directly affects student loading safety because passing traffic may not receive the full stop warning. The stop arm reinforces the red flashing lights with the familiar octagonal STOP sign. Without it, students crossing the road may be at greater risk.

  10. Question 10 of 15

    A driver completes a student stop: amber warning lights before the stop, full stop, parking brake as required, mirrors checked, students controlled at 10+ feet, traffic verified stopped, signal given for crossing, students watched across, and mirror sweep completed before pulling away. What does this show?

    Show answerHide answer

    Answer: A. The driver has followed a comprehensive school bus stop procedure with warning signals, danger-zone awareness, traffic verification, student control, and pre-departure checks

    A complete school bus stop includes advance warning, a safe stop, mirror checks, student control, traffic verification before signaling students to cross, crossing supervision, and a final mirror sweep before moving. The driver must keep control of the stop and move only when students are safely clear.

  11. Question 11 of 15

    A school bus stop arm sticks halfway out and will not fully extend. What is the safest decision?

    Show answerHide answer

    Answer: D. Do not use the bus for student transport until the stop arm is repaired

    A stop arm that only extends partway may not clearly display the STOP sign to approaching traffic. The driver should report the defect and the bus should not be used for student transport until the stop arm extends and retracts properly.

  12. Question 12 of 15

    After unloading students, the driver cannot see one child who had been crossing in front of the bus. What should the driver do?

    Show answerHide answer

    Answer: C. Do not move , set the parking brake, locate the child visually, and check the front danger zone before moving

    If a student who was crossing in front of the bus is no longer visible, the driver must not move. The driver should secure the bus, check mirrors and the windshield view, and if necessary get out and look. The bus should not move until the driver has visually confirmed the student's location and that the student is safely clear.

  13. Question 13 of 15

    Which defect most directly affects the driver's ability to see students in the front danger zone?

    Show answerHide answer

    Answer: A. Broken or badly misadjusted crossover mirror

    Crossover mirrors are designed to help the driver see the area immediately in front of the bus, including the front danger zone where small children may be hard or impossible to see directly from the driver's seat. A broken or badly misadjusted crossover mirror can prevent the driver from confirming that the area is clear before moving.

  14. Question 14 of 15

    Before opening the service door at a student stop, what should the school bus driver do?

    Show answerHide answer

    Answer: D. Activate amber warning lights before the stop, come to a complete stop, set the parking brake as required, check mirrors, then open the service door so red lights and stop arm activate if equipped

    A common school bus stop sequence is to activate amber warning lights before the stop according to state law or local procedure, come to a complete stop, set the parking brake as required, check mirrors and traffic, then open the service door so red flashing lights and stop arm activate if equipped.

  15. Question 15 of 15

    What mirror systems are required on a school bus?

    Show answerHide answer

    Answer: C. Outside left and right rectangular (flat) mirrors, outside left and right convex (spot) mirrors, AND two crossover (curb-side) mirrors visible from driver's seat for the area immediately in front

    Required school bus mirror systems: (1) RECTANGULAR (flat) mirrors on both sides , view directly behind/along bus; (2) CONVEX (spot) mirrors on both sides , wider view of areas closer to bus; (3) CROSSOVER mirrors , large convex mirrors mounted on front fenders, allowing driver to see the entire front danger zone and immediate side curb area. All must be functional before each route.

0 / 15Answer the questions above to see your score

Railroad crossing and loading zone questions are the ones to know cold. They're very specific.

Your state may have extra school bus rules, so check your state's manual too.

Want more questions like these?

CDL Pro has 1,000 practice questions with explanations, timed practice exams, and weak-area drills.

← Back to blog