This is a mixed practice test pulled from every part of the CDL written tests: general knowledge, air brakes, combination vehicles, pre-trip inspection, and the endorsements.
It's a good way to see where you stand. Take it without looking anything up and see which sections give you trouble.
-
Question 1 of 20
What should a driver check about steps and entry areas?
Show answerHide answer
Answer: B. Step treads non-slip and not worn smooth, step lights working, steps secure (not loose), no damage to riser or handrails, properly lit when needed
Step checks: treads have non-slip surface (rubber/abrasive coating intact), step lights working (illuminate steps at night), no looseness when weight applied, no cracks/damage to step or riser, surrounding handrails secure. Falls during boarding/exiting are a common passenger injury , small step defects cause big falls.
-
Question 2 of 20
What is the main goal of proper lane positioning in a CMV?
Show answerHide answer
Answer: A. To leave safe space around the vehicle and stay centered in the lane
Proper lane positioning means staying centered with safe space on both sides. This helps avoid roadside hazards, prevents sideswipes, and keeps the trailer tracking within the lane.
-
Question 3 of 20
A driver places HazMat shipping papers in the trailer nose behind the freight. Why is this wrong?
Show answerHide answer
Answer: C. Papers must be accessible to the driver AND emergency responders , putting them in the trailer makes both impossible
Emergency responders are trained to look in the driver's compartment or driver-door holder for HazMat shipping papers. If the papers are in the trailer behind cargo, they may not be accessible during an inspection or emergency. Shipping papers must be kept in the required accessible location.
-
Question 4 of 20
Which condition should a driver look for when inspecting suspension parts?
Show answerHide answer
Answer: D. Cracked, broken, missing, or shifted parts
Suspension parts (leaf springs, air bags, shock absorbers, U-bolts, mounts, hangers, torque rods) should be checked for cracks, breaks, missing parts, shifted components, and damaged mounts.
-
Question 5 of 20
What is stab braking?
Show answerHide answer
Answer: B. Applying the brakes fully, releasing them when wheels lock, then reapplying after the wheels start rolling
Stab braking is used on non-ABS vehicles for emergency stops: apply brakes fully, release when wheels lock, wait for wheels to start rolling, then reapply. This cycle should take less than one second. It maximizes stopping force while preserving steering control.
-
Question 6 of 20
What hazard does Class 8 cover?
Show answerHide answer
Answer: C. Corrosives , materials that destroy human skin OR severely corrode metal (acids, bases like sulfuric acid, sodium hydroxide)
Class 8 = Corrosives. Black/white label with hand and metal being eaten by liquid drops. Includes strong acids (sulfuric, hydrochloric, nitric) and strong bases (sodium hydroxide, potassium hydroxide). Causes skin burns on contact and corrodes steel. Common loads include battery acid and industrial cleaners.
-
Question 7 of 20
Which standing-passenger situation is unsafe and prohibited?
Show answerHide answer
Answer: C. A passenger standing in the stairwell near the door OR in front of the standee line
Stairwell standing is prohibited because: (1) interferes with door operation, (2) high fall risk in a stop, (3) potential ejection if door opens. Standing in front of the standee line is prohibited for the same reasons plus driver vision/interference. Driver should direct standing passengers behind the line or to available seats.
-
Question 8 of 20
What is the purpose of a post-trip inspection?
Show answerHide answer
Answer: D. To identify and report defects after the trip so they can be corrected
A post-trip inspection helps identify defects found during or after the trip so they can be reported and repaired before the vehicle is used again.
-
Question 9 of 20
During the engine compartment inspection, the driver finds loose hardware near moving belts and pulleys. What is the main risk?
Show answerHide answer
Answer: A. Loose parts can be thrown by moving belts, causing damage or injury
Loose parts near moving belts, pulleys, or fans can be caught, thrown, or cause component damage. They should be secured or removed before operating.
-
Question 10 of 20
A driver has driven 8 cumulative hours since their last qualifying 30-minute break. What must happen before the driver continues driving?
Show answerHide answer
Answer: A. The driver must take a qualifying 30-minute non-driving break
After 8 cumulative hours of driving without a qualifying 30-minute break, the driver must take a qualifying 30-minute non-driving break before continuing to drive.
-
Question 11 of 20
A driver pulling triples sees debris ahead but has traffic beside the vehicle. What is the safest first response?
Show answerHide answer
Answer: A. Slow smoothly with the foot brake, check mirrors, and avoid sudden swerving
Triples are highly vulnerable to rearward amplification from sudden steering. If debris appears ahead and traffic is beside the vehicle, the driver should slow smoothly, keep the vehicle stable, check mirrors, and avoid abrupt lane changes. The safest response depends on the size of the debris, traffic, speed, and available escape path.
-
Question 12 of 20
A driver wants to know when the air brake system safety valve releases. At what pressure is the safety valve typically set?
Show answerHide answer
Answer: D. 150 psi
The safety valve is typically set to release at 150 psi. This protects the air brake system from damage caused by excessive pressure if the governor fails to control compressor cut-out.
-
Question 13 of 20
A driver finds a cracked trailer crossmember near the landing gear mount. What is the safest action?
Show answerHide answer
Answer: A. Report it and have the trailer inspected before operating , frame damage near load points is a serious defect
A cracked crossmember near the landing gear is a serious defect because the landing gear supports heavy trailer weight when uncoupled. Structural damage near load points should be reported and inspected before operating.
-
Question 14 of 20
Students begin walking toward the bus before the driver has stopped and signaled them. What should the driver do?
Show answerHide answer
Answer: D. Complete the stop safely, set brake, then signal students to approach , children should be taught to wait for the driver's clear signal before approaching
Students should wait for the bus to fully stop and for the driver's signal before approaching. The driver controls when students move toward the bus: stop first, secure the bus as required, check traffic and mirrors, then signal students when it is safe.
-
Question 15 of 20
A driver follows the approved HazMat route, keeps shipping papers and ERG accessible, follows attendance rules when they apply, avoids smoking violations, shuts the engine off during refueling, reports suspicious cargo questions, and knows the NRC number if a reportable incident occurs. What does this show?
Show answerHide answer
Answer: A. The driver is applying ALL key HazMat route, emergency, security, and incident response responsibilities , comprehensive compliance
This shows broad HazMat responsibility: route compliance, accessible emergency information, attendance/security awareness, no-smoking and refueling safety, suspicious-activity reporting, and incident-reporting readiness. The driver is applying key HazMat route, emergency, security, and response responsibilities.
-
Question 16 of 20
What is reasonable suspicion testing based on?
Show answerHide answer
Answer: D. A trained supervisor's observations of possible drug or alcohol use
Reasonable suspicion testing is based on specific observations by a trained supervisor , such as appearance, behavior, speech, or body odor , that may indicate drug or alcohol use.
-
Question 17 of 20
A CDL driver is convicted of leaving the scene of an accident while operating a CMV. How is this generally treated?
Show answerHide answer
Answer: D. As a major offense that can lead to disqualification
Leaving the scene of an accident while operating a CMV is a major offense and can result in CDL disqualification.
-
Question 18 of 20
A tractor-trailer is under the 80,000 lb gross weight limit, but the drive axles weigh 36,000 lb. What should the driver do?
Show answerHide answer
Answer: D. Adjust or redistribute the load before continuing , the drive tandems exceed the 34,000 lb limit
Each axle group has its own legal limit. If drive tandems are 36,000 pounds where the applicable tandem limit is 34,000 pounds, the load must be adjusted before continuing. The driver may be able to slide the trailer tandems forward to shift weight from the drive axles to the trailer axles, if the trailer tandems remain within legal limits, or the cargo may need to be redistributed.
-
Question 19 of 20
Why should a driver pay close attention to mountain warning signs?
Show answerHide answer
Answer: A. They provide advance notice of grades, curves, runaway truck ramps, and other hazards
Mountain warning signs give advance notice of steep grades, sharp curves, escape ramps, narrow roads, and other hazards. CMV drivers need this information early to choose safe speed and gear.
-
Question 20 of 20
Why is load distribution important?
Show answerHide answer
Answer: D. It affects steering, braking, axle weight, and rollover risk
Proper load distribution keeps axle weights legal, steering responsive, braking balanced, and rollover risk low. Heavy cargo concentrated too high raises the center of gravity (rollover); too far forward overloads steer axle; too far rearward overloads tandem.
Look at which sections you missed, not just your score. That tells you which test to focus on next.
Ready to dig into one section? Try the practice tests for general knowledge, air brakes, combination vehicles, and each endorsement below.
Want more questions like these?
CDL Pro has 1,000 practice questions with explanations, timed practice exams, and weak-area drills.