If you're driving anything with air brakes, you need to pass the air brakes test, and it's one a lot of people underestimate. It's not hard once it clicks, but there are a bunch of specific numbers and steps to know.
These 15 questions cover how the system works, the gauges and warning signals, spring brakes, brake adjustment, and the air brake check you'll do on your pre-trip.
-
Question 1 of 15
What is the safest braking strategy before descending a steep grade?
Show answerHide answer
Answer: D. Choose a proper low gear before the descent and control speed before it builds
Before a steep descent, choose a low gear (typically one lower than the gear used to climb the same grade) and control speed early. The engine and drivetrain do most of the speed control, sparing the service brakes from overheating.
-
Question 2 of 15
A driver inspecting a brake chamber finds it cracked, loose, and missing one mounting bolt. Is this condition safe to operate?
Show answerHide answer
Answer: B. No , a cracked, loose, or leaking brake chamber can reduce or eliminate braking on that wheel
Brake chambers must be securely mounted, free of cracks or leaks, with all mounting bolts in place. A loose or leaking chamber can reduce or eliminate braking on that wheel.
-
Question 3 of 15
During a static leakage test on a combination vehicle, what is the maximum allowable air loss in one minute?
Show answerHide answer
Answer: A. 3 psi
For a combination vehicle (tractor with trailer), static air pressure loss must not exceed 3 psi in one minute. Combinations have more lines and connections, so a slightly higher leak rate is allowed , but anything beyond it indicates excessive leakage.
-
Question 4 of 15
What is the typical normal operating range for air pressure in a dual air brake system?
Show answerHide answer
Answer: D. About 100 to 125 psi
The normal operating range is typically about 100 to 125 psi , between the governor cut-in (around 100 psi) and cut-out (around 125 psi). The compressor cycles on and off to keep pressure within this range.
-
Question 5 of 15
Why is proper brake adjustment important on an air brake vehicle?
Show answerHide answer
Answer: D. Out-of-adjustment brakes may not apply with full force
If brakes are out of adjustment, the pushrod must travel farther before the brake applies, reducing braking force at the wheel. Out-of-adjustment brakes are the most common cause of CMV brake-related crashes , they increase stopping distance and can leave the brake unable to apply fully.
-
Question 6 of 15
What is the purpose of air storage tanks?
Show answerHide answer
Answer: D. To store compressed air until it is needed by the brake system
Air storage tanks (also called reservoirs) hold compressed air for the brake system. They provide enough stored air to allow several brake applications even if the compressor stops working.
-
Question 7 of 15
During the spring brake pop-out test, the parking brake controls do not pop out even when air pressure drops very low. What should the driver do?
Show answerHide answer
Answer: B. Report the defect and do not operate until the spring brake system is checked
If the spring brake controls do not pop out when pressure drops into the expected low-pressure range, the parking/emergency brake system may be defective. The driver should report the defect and not operate until the spring brake system is checked.
-
Question 8 of 15
Per FMCSA regulation, before pressure drops below what level must the low-air warning device activate?
Show answerHide answer
Answer: C. 60 psi
The low-air warning must activate before air pressure drops below 60 psi. This threshold gives the driver advance warning before pressure falls into the range (about 20-45 psi) where spring brakes automatically apply.
-
Question 9 of 15
A driver of a non-ABS vehicle needs to brake hard in an emergency. Which technique should the driver use?
Show answerHide answer
Answer: C. Stab braking or controlled braking, depending on the situation
On a non-ABS vehicle, the driver uses controlled braking (firm pressure without lockup) or stab braking (release-and-reapply after lockup). Both techniques aim to stop hard while keeping steering control.
-
Question 10 of 15
A driver watches the air pressure gauge and sees the compressor start pumping around 100 psi and stop around 125 psi. What pressures are these?
Show answerHide answer
Answer: A. Cut-in around 100 psi; cut-out around 125 psi
Cut-in pressure (when the compressor starts pumping) is typically around 100 psi. Cut-out pressure (when the compressor stops pumping) is typically around 125 psi. Exact values vary by manufacturer but should be within ranges set by the system design.
-
Question 11 of 15
A driver completes the static leakage test on a combination vehicle and sees a 4 psi loss in one minute. What should the driver conclude?
Show answerHide answer
Answer: B. The result fails the static leakage limit (3 psi) for a combination vehicle
Combination vehicle static leakage limit is 3 psi/min. A 4 psi loss exceeds this limit and indicates excessive leakage. The driver may be confusing this with the applied limit (4 psi for combination), but static and applied tests have different limits.
-
Question 12 of 15
During the air brake check, pressure drops below 60 psi but the warning light and buzzer never come on. What should the driver do?
Show answerHide answer
Answer: A. Report the defect and do not drive until the warning device is repaired
If the low-air warning does not activate before pressure drops below 60 psi, the warning system is defective. The vehicle must not be operated until repaired. Without the warning, the driver could lose enough pressure for spring brakes to auto-apply while driving.
-
Question 13 of 15
A driver rides the service brakes lightly all the way down a long grade. What is the most likely danger?
Show answerHide answer
Answer: A. The brakes may overheat and fade, possibly leading to brake failure
Riding the brakes on a long downgrade overheats them and causes brake fade. The proper technique is to choose a low gear (lower than what was used climbing the same grade) and use snub braking , brake firmly to slow 5 mph, then release to let brakes cool.
-
Question 14 of 15
What happens when the driver presses the brake pedal to apply the service brakes?
Show answerHide answer
Answer: A. Air pressure is sent to the brake chambers to apply the brakes
When the driver presses the brake pedal (sometimes called the foot valve or treadle valve), air pressure is delivered from the storage tanks through the service brake system to the brake chambers, which apply the foundation brakes.
-
Question 15 of 15
In a tractor-trailer combination, what is the difference between the trailer hand valve and the parking brake?
Show answerHide answer
Answer: A. The trailer hand valve applies trailer brakes only; the parking brake applies spring brakes for parking
The trailer hand valve, sometimes called the trolley valve, applies the trailer service brakes only. It is not a parking brake and should not be used to hold a parked vehicle because air can leak away and release the brakes. The parking brake control applies spring brakes for parking.
If the numbers tripped you up, like pressures and leak rates, write the ones you missed on a card and go over them every day until test day.
The air brake check is also part of your skills test, so it's worth knowing the steps cold, not just for the written test.
Want more questions like these?
CDL Pro has 1,000 practice questions with explanations, timed practice exams, and weak-area drills.