The HazMat endorsement test has a lot of rules to memorize: hazard classes, which loads need placards, what goes on the shipping papers, what can and can't be loaded together, and what to do in an emergency.

These 15 questions hit all of it. Placards and loading rules are where most people lose points, so slow down on those.

  1. Question 1 of 15

    Which statement best describes the driver's HazMat paperwork responsibility?

    Show answerHide answer

    Answer: A. Verify required documents are present, complete, signed by shipper, consistent with the load, and properly placed , before AND during transport

    The driver's documentation responsibilities include verifying that required papers are present and complete, confirming the shipper's certification is present when required, checking consistency with placards and package markings, keeping the papers in the required accessible location, and presenting them on demand at inspections.

  2. Question 2 of 15

    Which three parties share responsibility in safe HazMat transportation?

    Show answerHide answer

    Answer: D. The shipper, the carrier, and the driver , each has specific responsibilities under federal regulations

    Three parties: (1) SHIPPER prepares HazMat for transport , classifies, packages, labels, prepares shipping papers; (2) CARRIER accepts material and transports it; (3) DRIVER inspects vehicle and load, follows rules, watches for problems en route. Each has independent legal duties.

  3. Question 3 of 15

    Why must HazMat packages be secured during transportation?

    Show answerHide answer

    Answer: C. Movement causes damaged packages, leaks, spills, and possible reactions , federal securement rules apply

    HazMat packages must be secured against shifting during normal transportation conditions, including acceleration, braking, and turning. A loose package can be damaged, leak, spill, or contact incompatible materials.

  4. Question 4 of 15

    Which vehicle is properly placarded?

    Show answerHide answer

    Answer: B. A vehicle with the required placards visible and readable on all 4 required sides, matching the shipping papers

    Properly placarded means the required placards are visible, readable, correctly displayed on all required sides, and consistent with the shipping papers. Stored, hidden, old, or wrong-class placards do not properly communicate the current hazard.

  5. Question 5 of 15

    What hazard does Class 1 represent, and what is a key feature of Class 1 placards/labels?

    Show answerHide answer

    Answer: D. Explosives , orange-colored placard/label with explosion symbol; has 6 divisions from 1.1 mass explosion hazard through 1.6 extremely insensitive explosive articles

    Class 1 covers explosives. Class 1 labels and placards are orange with an explosion symbol. The six divisions are 1.1 mass explosion hazard, 1.2 projection hazard, 1.3 fire hazard, 1.4 minor explosion hazard, 1.5 very insensitive explosives, and 1.6 extremely insensitive explosive articles.

  6. Question 6 of 15

    A driver hauling hazardous materials realizes mid-trip that the planned route includes a restricted bridge. What is the correct action?

    Show answerHide answer

    Answer: C. Reroute legally BEFORE reaching the bridge , placards/papers being correct don't override route restrictions

    Route restrictions are independent of placarding/documentation compliance. Even a perfectly placarded HazMat load violates the law by entering a restricted area. Plan routes ahead with HazMat-specific tools. If you discover a restriction mid-trip, exit before reaching it and find an approved alternate route.

  7. Question 7 of 15

    A driver receives shipping papers that list a proper shipping name and identification number but leave the hazard class blank. What should the driver do?

    Show answerHide answer

    Answer: D. Do not accept or transport the load until the shipper completes the missing hazard class entry

    The required HazMat description must be complete. A blank hazard class could leave inspectors or responders without key hazard information. The driver should not guess or fill in missing HazMat information. The shipper must correct the shipping paper before the load is accepted or transported.

  8. Question 8 of 15

    A driver is handed shipping papers for a HazMat load but notices the material description seems incomplete. What should the driver do?

    Show answerHide answer

    Answer: C. Refuse the load and require the shipper to correct the shipping papers before transport

    HazMat shipping papers must be complete and accurate, including the proper shipping name, hazard class, identification number, packing group when required, quantity, and emergency response information. The driver should not accept a load with incomplete papers until the shipper or another authorized/qualified person corrects the issue.

  9. Question 9 of 15

    What special rules apply when loading Class 1 (Explosives) , particularly Divisions 1.1, 1.2, and 1.3?

    Show answerHide answer

    Answer: C. Cargo heaters cannot be used; trailer floor must be tight with no exposed metal/nails; engine off; no smoking within 25 feet; doors closed during transit

    Class 1 explosives, especially Divisions 1.1, 1.2, and 1.3, have strict loading rules. Packages must be handled carefully, protected from heat and sparks, and loaded only in equipment that meets the required condition. No smoking is allowed within 25 feet, and the engine should be off unless regulations allow it to run for necessary equipment.

  10. Question 10 of 15

    A trailer delivered a flammable liquid load yesterday and is now empty, cleaned, and no longer requires placards. What should happen to the old placards?

    Show answerHide answer

    Answer: C. They should be removed or covered if no longer required , leaving them displayed is a HazMat communication violation

    Placards represent CURRENT hazards. An empty/cleaned trailer no longer carrying HazMat shouldn't display HazMat placards. Many trailers use removable placard cards or slide-in holders for easy switching. NOTE: tank trailers must remain placarded until they're properly cleaned/purged , residual vapors can still ignite.

  11. Question 11 of 15

    Which hazard class examples are correctly matched?

    Show answerHide answer

    Answer: A. Class 3 flammable liquid (gasoline); Class 8 corrosive (sulfuric acid); Class 2.3 poison gas (chlorine)

    Common examples by class include: Class 1 explosives; Class 2 gases such as propane or chlorine; Class 3 flammable liquids such as gasoline; Class 4 flammable solids or dangerous-when-wet materials; Class 5 oxidizers and organic peroxides; Class 6 toxic or infectious substances; Class 7 radioactive materials; Class 8 corrosives such as acids or caustics; and Class 9 miscellaneous hazardous materials.

  12. Question 12 of 15

    What is the National Response Center, and what is the phone number for reporting major HazMat incidents?

    Show answerHide answer

    Answer: D. Federal incident reporting hotline at 1-800-424-8802 (24-hour) , call for spills, fires, casualties, or evacuations

    The National Response Center at 1-800-424-8802 is the federal contact point for reporting reportable HazMat incidents. It is separate from 911, which handles local emergency response, and CHEMTREC or other emergency contacts, which may provide technical guidance.

  13. Question 13 of 15

    What is the main purpose of HazMat shipping papers?

    Show answerHide answer

    Answer: D. To identify the hazardous material being transported and provide all required information for inspectors and emergency responders

    HazMat shipping papers identify the material and provide required transportation information such as identification number, proper shipping name, hazard class, packing group when applicable, quantity, emergency response information, and shipper certification when required. They help inspectors and emergency responders understand what is being transported.

  14. Question 14 of 15

    Why is HazMat training required?

    Show answerHide answer

    Answer: C. Drivers must know how to recognize hazards, follow rules, handle emergencies, and meet security requirements , recertification required at specific intervals

    HazMat training covers: general awareness, function-specific (the driver's actual duties), safety procedures, security awareness, and in-depth security plans for certain materials. Training is required initially within 90 days of new HazMat duties, then at least every 3 years.

  15. Question 15 of 15

    What is the general rule about loading poisonous materials with food or feed?

    Show answerHide answer

    Answer: C. Poisonous materials generally must not be loaded with food, feed, or anything intended for human or animal consumption unless the regulations allow it

    Drivers must protect food, feed, and other products intended for human or animal consumption from contamination by poisonous materials. In general, poison/toxic materials must not be loaded with food or feed unless the specific regulations and packaging conditions allow it. When in doubt, do not accept the mixed load until it is verified.

0 / 15Answer the questions above to see your score

The placard rules and the segregation rules are the two areas to drill hardest. They're specific, and the test loves asking about them.

Remember you'll also need a background check for the HazMat endorsement, so check with your state on how that works.

Want more questions like these?

CDL Pro has 1,000 practice questions with explanations, timed practice exams, and weak-area drills.

← Back to blog